Tag Archives: retro

DIY reclaimed lumber hanging Edison bulb chandelier

This DIY reclaimed lumber chandelier with hanging Edison bulbs is easy and quite self-explanatory, though I will explain somewhat. Here’s what you’ll need,

Parts for Fixture

  • piece of lumber
  • 2x lengths of chain
  • 4x open/close chain links, to affix the chain to the eyelets you’ll screw to the board
  • 4x screw eyelets, to secure the chain to the lumber
  • 2x screw hooks, to hook the chain to the ceiling *screwed into solid wood joists
  • one or more junction boxes depending on the size of the wood
  • one or more hanging lights, cord, socket, bulb (see below)
  • a cover for the ceiling junction box plastic or otherwise, you may have to cut a notch for the power cable

Parts for Lights

Once you’ve selected your lumber, drill a hole for each light cord. I started with a spacious zig-zag pattern but it’s whatever you like really. Affix junction boxes to the top-side of the lumber and wire the lights into them. Screw an eyelet into each corner of the top-side of the lumber, at least an inch in from any side.

If the lumber is extra heavy you could consider another length of chain and place two more eyelets to support a chain in the center. If ceiling joist placements allows you could also use four lengths of chain straight up to four hooks instead of the swing system I employed.

Screw the hooks firmly into ceiling joists, hang the fixture and wire whichever junction box is closest into the ceiling electrical. If possible the power cable would be less noticeable if it snaked to the ceiling along one of the support chains.

Once hung you can adjust the heights of the hanging bulbs and coil the extra cable on top, it’s not coiled very neatly in some of these pictures but I have since remedied that. There you have it.

If you’re interested in other Edison-style lighting ideas check out DIY steampunk-style iron pipe Edison fixture and the reason I have so many Edison bulbs kicking around, Maker Wedding: Rustic Edison-style hanging light fixtures.

DIY steampunk-style iron pipe Edison fixture

I’ve been seeing these types of steampunk black malleable iron on the net for years; it was only a matter of time before I went and made one. The texture of the iron combined with the warm vacuum-tube glow is quite an amazing effect, and they certainly look easy to make. Previous trips to the hardware store had only resulted in the question of what socket will fit into these types of pipes? I found myself with some spare time this past Saturday, so I went to the local hardware store and laid out 15 or 20 iron gas pipe fittings in the aisle and designed a 4-bulb fixture — roughly designed that is.

While designing the fixture be careful not to screw the fittings together too tightly as they can bind, also keep in mind these fittings will turn your hands black and the sharp threads can easily shred your hands if you slip. This being my first attempt I kept it relatively simple, keep in mind that you will have to thread wiring through all the bends and turns at some point.

I used the largest malleable iron piping I found, which had an inner diameter of 1 inch on the female threaded sections. I then purchased some basic keyless (no switch) brass sockets. These did not fit in the pipes, though I didn’t mind the look of the brass sockets extending from the fixture so I started with that.

The rounded base of the sockets became a problem as when they were wired and threaded into the fixture they lolled this way or that rather than extending straight from the fitting. I tried bulking up the base of the sockets with electrical tape, but they still slipped. I then tried removing the rounded bottom section yet the upper brass part was still too large in diameter to fit in the pipe.

Then I discarded everything but the bare socket with its bakelite base, the middle portion in the exploded image below (not the exact socket, but very similar). These almost fit, I had to crack/shave/cut off some protrusions from the bakelite base. Discarding the brass and cardboard meant that the socket had no protection or isolation for the wiring leads, for this reason I wrapped the hot lead with some electrical tape to isolate it and then ran one wrap of electrical tape around the entire socket. This extra bulk meant I had to twist and fiddle but they still fit in the pipe. If you fiddle so much that you think the electrical tape may have shredded, take it out, replace the tape and start again. It’s better to be safe.

Even though the sockets had no ground lead it was important when wiring be sure to wire all sockets in the same fashion and keep track of which wire is hot as they will all be combined at some point and you don’t want to short the wrong lead to the iron fixture structure.

While threading wire through the fixture you can unscrew fittings but be careful not to twist the wiring too much inside around elbows.

With the sockets wired and the wiring threaded through the fixture the next step was mounting it to the ceiling or wall. The wall mount fitting, pictured right, is not large enough to cover a junction box. For this reason I used a white plastic cover, however screwing the wall mount fitting to the plastic cover would not be strong enough to support the fixture (iron is heavy).

Another problem was that the wall mount fitting’s screw holes would block the plastic cover’s screw holes. I decided to use a steel junction box cover on top of the plastic cover to support the fixture. I drilled a center hole in both covers, two holes to line up with two of the iron mount’s screw holes and ensured that one of the remaining two screw holes in the iron mount fitting lined up with one of the plastic cover’s screw holes. This meant that the iron fitting would not be centered on the plastic cover, but it did allow access to both of the plastic cover’s screws even after the iron fitting was secured.

In this manner the iron fitting could be bolted to the steel cover, through the plastic cover and still allow access to the plastic cover’s screw holes in order to affix the entire assembly to the junction box.

The photo above shows the steel cover which has been drilled, in this photo the white plastic cover has not had the center hole drilled for the wires yet. I’m confident this system would have worked with a full sized junction box, however once I removed the old fixture I realized my desired location had an old-style smaller junction box and this system wasn’t going to work.

As it turns out, mounting to an old-style smaller junction box is even easier as the two junction box mounting bolts do line up with the iron fitting and therefore there wasn’t a need for the steel plate after-all. I put bolts right through the iron mount fitting, the white plastic cover and into the junction box, which allowed the junction box to directly support the weight of the fixture.

If you’re confident wiring fixtures, outlets, sockets and such this should be right in your comfort zone — if not perhaps enlist a friend who is to help out.

If you’re interested in other Edison-style lighting ideas check out DIY reclaimed lumber hanging Edison bulb chandelier and the reason I have so many Edison bulbs kicking around, Maker Wedding: Rustic Edison-style hanging light fixtures.

Maker Wedding: Rustic Edison-style hanging light fixtures

Edison-style light fixtures


After deciding to have our wedding in a barn which had been converted into an event space my thoughts turned to lighting. With the rustic nature of the barn and the impressively high ceilings, one type of lighting sprang to mind instantly — Edison-style bulbs.

I’ve long been a fan of cloth covered wire, so I decided to make each bulb a separate hanging fixture with twisted cloth covered wire, an outlet and a bulb socket. This made the setup completely modular, allowing us to adjust for electrical loads and support almost any arrangement of bulbs. Each fixture would be plugged into a multi-outlet extension cord and secured with a small electrical tie. Each multi-outlet extension cord was plugged in through a lamp dimmer, which was also affixed with an electrical tie to avoid disconnections.

The parts I sourced are below, feel free to comment with better prices. These sockets are three-stage but the bulbs are not, bulbs could be swapped for three-stage bulbs or the sockets for single stage, but it all works regardless. Three-stage bulbs may eliminate the need for the dimmers, but having the dimmers made adjustments quite easy.

To wire the hanging fixtures I first slipped one piece of heat shrink tubing (without heating yet) over the cloth ends encompassing both leads. I then worked the cloth back, stripped the insulation inside and then attached the leads to the socket and plug. Once the leads were secured I shimmied the heat shrink as close to the connections as it would go and blasted it with the heat gun (or, oh my, harassed it with the soldering iron).

Before you go wild with these, do some math to see how many fixtures you should be plugging into each extension cord, and how much wattage your dimmer can support — watch dimmers closely at first, they may heat up, but make sure they’re not melting!

If you’re interested in other Edison-style lighting ideas and/or wondering what I did with all these lights afterwards check out DIY steampunk-style iron pipe Edison fixture and DIY reclaimed lumber hanging Edison bulb chandelier.

Update: Close to a year following our wedding we sent these lights, along with a simple handcrafted fixture, to family and friends as a token of our appreciation and as a keepsake from our wedding. Details about the Edison light thank you packages can be found here.

Parts